In a normal, unsuppressed semiautomatic pistol gunshot, you pull the trigger, a precise little pin strikes the back-center of a bullet, this causes the gunpowder in the back of the bullet to spark and ignite and explode. The projectile portion of the bullet rides the wave of the explosion at supersonic speed down the barrel of the gun, which determines the direction of the path. There is an initial increase of backpressure of gas between the projectile and the back of the barrel, but semiautomatic weapons make use of this to push back the slide, expelling the spent casing and that gas and allowing the spring in the magazine to push the next round into place for the next shot, also significantly reducing recoil in the process.
Suppressors (or “silencers”) work by slowing the bullet down and altering the propulsion gas path. Subsonic speeds means no sonic boom. The downside is that you must manually cycle each round yourself, and you will likely experience more recoil per shot.
Afaik, suppressors are pretty damn hard to legally obtain, so my knowledge of them is a combination of my firsthand accounts with my unsuppressed guns, secondhand accounts of suppressors, a moderate understanding of physics, and some guesswork. I could be wrong about some of this, but this is my general understanding that I carry around with me.
I don’t want to be a hater, but you’re wrong about a lot of things in this post. Supressors do not slow a projectile, and in most cases actually increase muzzle velocity due to increased dwell time for gas expansion. They suppress muzzle flash and report by containing said gasses. Sonic booms still happen, and supressors work more effectively with specific sub sonic ammunition, which is usually achieved with a heavier projectile weight lowering the velocity.
I’m not trying to dunk on you here, just trying to educate.
Obtaining a supressor isn’t too difficult, but you do have to be thoroughly screened by the ATF after submitting photos, fingerprints, and a form, and a $200 tax, which leads me to believe this suppressor was homemade and lacked a Nielsen device, see my thread above.
It’s A LOT to learn, and has been a primary interest of mine for a couple days, so I love sharing. I also love your big pp energy for updating the original comment.
In a normal, unsuppressed semiautomatic pistol gunshot, you pull the trigger, a precise little pin strikes the back-center of a bullet, this causes the gunpowder in the back of the bullet to spark and ignite and explode. The projectile portion of the bullet rides the wave of the explosion at supersonic speed down the barrel of the gun, which determines the direction of the path. There is an initial increase of backpressure of gas between the projectile and the back of the barrel, but semiautomatic weapons make use of this to push back the slide, expelling the spent casing and that gas and allowing the spring in the magazine to push the next round into place for the next shot, also significantly reducing recoil in the process.
Suppressors (or “silencers”) work by slowing the bullet down and altering the propulsion gas path. Subsonic speeds means no sonic boom. The downside is that you must manually cycle each round yourself, and you will likely experience more recoil per shot.
Afaik, suppressors are pretty damn hard to legally obtain, so my knowledge of them is a combination of my firsthand accounts with my unsuppressed guns, secondhand accounts of suppressors, a moderate understanding of physics, and some guesswork. I could be wrong about some of this, but this is my general understanding that I carry around with me.
I don’t want to be a hater, but you’re wrong about a lot of things in this post. Supressors do not slow a projectile, and in most cases actually increase muzzle velocity due to increased dwell time for gas expansion. They suppress muzzle flash and report by containing said gasses. Sonic booms still happen, and supressors work more effectively with specific sub sonic ammunition, which is usually achieved with a heavier projectile weight lowering the velocity.
I’m not trying to dunk on you here, just trying to educate.
Obtaining a supressor isn’t too difficult, but you do have to be thoroughly screened by the ATF after submitting photos, fingerprints, and a form, and a $200 tax, which leads me to believe this suppressor was homemade and lacked a Nielsen device, see my thread above.
Not hating, happy to be educated! I’m not prideful enough to be upset by you taking the time :)
It’s A LOT to learn, and has been a primary interest of mine for a couple days, so I love sharing. I also love your big pp energy for updating the original comment.
https://youtu.be/nIbY6lo0RIw
Here’s an expert explaining it better.